Changing the White Ink Filter on the Brother GT3
customer
(1) Make sure the GT-3 is not in the middle of any operation and is turned off. (2) Gently twist the nut (counter clockwise) on the tube to remove it from the top portion of the white filter (same filter as the GT-782). Be careful of any ink spilling out....
Replacing the Platen Sheet on the Brother GT3
customer
It is recommended to change the platen sheet when it starts to crack, tera or peel. The Platen Sheet becomes dirty with inks and garment lint within time from use and operation. This actually helps the garments being printed to lay and hold flat on the platen when printing. You...
Wiper Cartridge Cleaning on the Brother GT3
customer
The Wiper Cleaner needs to be replaced regularly. Keep the Print Head Cap and Wiper Blade clean when replacing the Wiper Cleaner. If not, the waste ink may drop on a T-shirt in printing or mis-firing may not be easily improved. (1) With power on, press the platen eject button...
Cleaning the Fan Cover on the Brother GT-3
customer
(1) Power on the machine and Eject the Platen. (2) Power off the machine. (3) Open the front cover/lid. (4) Locate the Fan inside the printer. Grasp the side of the fan cover facing the rear and pull the cover away from the fan toward the left side of the...
Clean the Encoder Strip on the Brother GT-3
customer
(1) Select encoder strip cleaning from the maintenance menu on the panel, and follow the prompts ending with turning the machine off. (2) Loosen the four black thumb screws (do not remove) on the encoder cover, and remove the cover. (3) Slide the carriage to the right side of the...
Flushing a Print Head on the Brother GT-541
customer
(1) Take a print head out of GT-541. This work should not be done on the heads still mounted on the printer. Prevent ink spills over the printer. (2) Take the filter off and intake the air. (3) As the photo shows put the air into the head and drain...
Performing a Head Flush on the Brother GT-541
customer
(1) Seal the hole on the Filter Cartridge with adhesive tape, etc. (2) Replace the Waste Ink Cartridge. (3) Make sure GT-541 is not in the middle of any operation. (4) On the Control Panel, press the Platen Button to eject the Platen if it is not. (5) Press the...
Cleaning Lower Cap Tubes on the Brother GT-541
customer
Description: Actuates the Maintenance unit by using the sequence of measuring the pump pressure and clears any clogs and obstruction in tubes below Head Caps. Steps to accomplish and determine if clog occurs Please do not attempt this step until you have done a cap wiper cleaning, checked the wiper caste...
Remove Front and Back Cover on the Brother GT-541
customer
(1) Remove Back Cover. Unscrew 15 screws of Back Cover. Unscrew 1 screw pan at the body edge of Ground Wire: 220, Open Front Cover and raise Rear Cover from the bottom. (2) Remove the five screws bind (M4x8) (in the red circles shown below), and then...
Remove Maintenance Station on the Brother GT-541
customer
6-1-7. Replacing the Maintenance Unit Refer to "6-2-11. Replacing Maintenance PCB" when you replace Maintenance PCB. Preparation (1) Make sure GT-541 is not in the middle of any operation. (2) Press the OK Button on the Control Panel to open the Menu Display. (3) Press the Up/Down Button to select...
How to Remove the Cartridge Cover on the Brother GT-541 Printer
Paul Boody
Performing maintenance or replacing the cartridge cover on your Brother GT-541 printer is a breeze with these easy steps. Looking for replacement parts or accessories for your Brother GT-541 printer? Check out our shop for a wide selection of Brother printer parts. With these steps, you'll have your cartridge cover removed in no time for maintenance or replacement.
Removing the Control Box on the Brother GT-541
customer
6-2-7. Replacing Control Box When the PCBs inside are replaced, use GTService Tool to readjust firmware controls. Prepare a voltmeter (tester) and a thermometer and refer to the pages concerned. (1) Remove Power code. (2) Remove Operation Panel. Remove 4 screws at both sides. Unscrew the Print SW...
Removing the Front Frame Covers on the Brother GT-541
customer
7-1. Removing the Covers The following describes how to remove the Covers. (1) Rotate the Print Button Cover counterclockwise to remove it. (2) Remove the four screws truss (M4x6) (shown in the picture below), and then remove the Control Panel. (3) Turn over the Control Panel Cover, and then disconnect...
Removing the Control Panel on the Brother GT-541
customer
7-3. Disassembling the Control Panel (1) Rotate the Print Button Cover counterclockwise to remove it. (2) Remove the four screws truss (M4x6) (shown in the picture below), and then remove the Control Panel. (3) Turn over the Control Panel, and then disconnect the Flat Cable from the Pancel PCB. The...
Replacing the Ink Tubes on the Brother GT-541
customer
6-1-3. Replacing the Tubes The Tubes can be replaced for every color. The following procedure shows the example of replacing the Tube for "Cyan." The procedure is the same for other colors. (1) Make sure GT-541 is not in middle of any operation. (2) Press the OK Button on the...
Replacing the Needles on the Brother GT-541
customer
6-1-4. Replacing the Needles The Needle can be replaced for every color. The following procedure shows the example of replacing the Needle for "Cyan." The procedure is the same for other colors. (1) Make sure GT-541 is not in middle of any operation. (2) Press the OK Button on the...