Replacing the Print Head on Brother GT 541
customer
Replacing the Print Head on the Brother GT541 Garment Printer 6-1-2. Replacing the Print Heads The Print Head can be replaced for every color. The following procedure is for replacing the Black Print Head. The procedure is the same for other colors. (1) Make sure GT-541 is not in middle...
Print Head Nozzle Check on Brother GT541
customer
Learn how to clean the Print Head with Nozzle Checks on the Brother GT-541 Garment Printer (1) Check the printed pattern to identify which Print Head has the problem. If there is stripes (arrow 1) or line breaks (arrow 2), the Print Head of the color (in...
VIDEO General Maintenance for your Garment Printer
Paul Boody
Learn the essential maintenance required to keep your DTG HM1 at peak performance.
Replacing the Print Head on the DTG HM1 Garment Printer
Bambri Collaborator
Learn how to replace a print head on a Epson R1900 garment printer in this step by step video series
VIDEO Flushing the Ink lines on the DTG HM1
Bambri Collaborator
Video on Flushing the ink on the HM1 garment printer.
Replacing the DTG HM1 Ink System
customer
Prior to starting work on removing any components from your DTG HM1 Kiosk (in fact, any DTG printer) ensure that the main power has been switched off and disconnected from the printer. Also disconnect USB cable(s) from the rear of the printer. You may find it easier to have the printer in...
DTG HM1 Replacing the Head Cable and Mainboard
customer
Here are two PDF documents that explain how to replace or service the HM1 head cable and mainboard. HM1 Head Cable Part1.pdf HM1 Head Cable Part 2.pdf You can buy the Head Cables for your DTG HM1 here
DTG HM1 WIMS Filter Replacement
customer
There are two side of the Filter for the HM1C, an inlet side and a outlet side. Here the Inlet side has been marked to make it easier to see. It is important to understand how the ink flows through the circulation system. See Figure B....
Resetting the waste ink counter DTG HM1
Paul Boody
Learn how to reset the dummy waste tank on your HM1-C printer using the Epson adjustment program and USB dongle key.
Error codes for the DTG HM1
customer
The printer is busy. This may be a normal startup cycle or a head cleaning. If the carriage has moved, then the INK button has been pressed. Press the INK button again. The Epson mainboard believes that the waste tank is full (NOTE: this is not the...
DTG VIPER Replacing the Capping Station Epson 4880
customer
Epson 4880 Capping Station Replacement For the DTG Viper Buy the Capping Station for the DTG Viper and other Epson 4880 based garment printer Tools Required: #2 Phillips Screwdriver, Needlenose Pliers Download the Viper Capping Station Replacement PDF or view it here online. 1) Removal of the Blue Cover:...
DTG VIPER Replacing the Print Head Epson 4880
customer
Replacing the Printhead on the Epson 4880 Garment Printer Like the DTG Viper Download the PDF or use this online version Tools Required: #1 Phillips screwdriver, Tape (gaer’s or masking,not duct) 1) Release the carriage from the capping station. Bring the carriage close to the center of the machine. Fig.1...
Why Garment Ink sticks to Teflon Sheet
Paul Boody
Inks stick to Garment Printing Teflon sheet or Garment Printing Curing parchment paper when curing the final print? These quick tips will
Rainbow Effect when Garment Printing
Paul Boody
Learn the cause of Rainbow Effect while garment printing and how to remedy it.
Dull colors on a gray shirt with garment printer
Paul Boody
If you're experiencing dull colors on your DTG printer, try this trick to make the print more vibrant in the DTG RIP Pro software.
VIDEO remove Epson 4880 Neoflex Head and flush
customer
Here's a video on one of the most common fixes/repair/maintenance for a garment printer. Removing the Print Head. Whether you need to replace the neoflex printhead, clean it or just check to make sure it's not the cause of your problems, watching a video is the easiest way to get...