Table Motor Belt Tension Adjustment
customer
2.3 - Table Motor Belt Tension Adjustment Tools Needed 3/8th ratchet wrench Gates Tension Meter 3/32 Phillips screw driver 7/16 ratchet wrench (1) The best way to adjust the tension in the Table motor belt is to remove the entire table guide assembly from the printer. Before starting power down...
Table Belt Tension
customer
2.2 Table Belt Tension Tools Needed Phillips Screw Driver 11/32 Ratchet Wrench 10/32 ALlen Key / T-Handle Gates Belt Tension Meter or Equivalent (1) Move the table to the home position by pressing the TABLE button (table should be inside the printer). Remove the three Phillips screws from the bottom...
Carriage Belt Tension
customer
2.1 Carriage Belt Tension Tools Needed 7/16 Ratchet Wrench Gates Belt Tension Meter or equivalent (1) Loosen the two hex head bolts using a 7/16 ratchet wrench. The two hex bolts will be located on the far right underneath the belt pulley. See photo 2.1-1 (2) You can now adjust...
Step-by-Step Guide: Removing Ink Covers on the Brother GT-541 Printer
Dean Armando
Are you looking to perform maintenance or replace the ink covers on your Brother GT-541 printer? Follow these simple steps: Step 1: Remove the Screws and Washers Remove the four screws (M4x6) and three washers (highlighted in red circles in the image below). Next, remove the four pan-head screws (S/P...
Download the Epson 4880 Adjustment Program Here
Dean Armando
When installing a new motherboard/mainboard in your 4880 based garment printer, you will need to use the Epson 4880 Adjustment PRogram to pull the data off the EPROM and upload it to the new board. Unfortunately we can not offer any guidance on this, however if you do it and...
Print Engine Blown F2 Fuse
Dean Armando
The symptoms of a blown F2 fuse are as follows: The print head will not fire a single nozzle. The machine will power up normally, and the print head carriage will move back and forth normally but not a single nozzle will fire. If any nozzles fire, then the F2...
Reseat Ink Chip Holder Anajet FP125
customer
Issues relating to the ink chip holder will result in one or more LEDs being solidly lit on the LED board under the printer's cover. Most likely the ink chips may have moved off of their contacts and need to be reseated. It is also possible that one or more...
Best AnaRIP Setting to Use with Your Anajet mPower
customer
Symptoms: Prints are not coming out vibrant, wash out or colors are bleeding. White ink not bright enough. Possible Causes: Light garments should be printed best using the default setting of Medium drop size and Normal quality setting. Make sure that before you start a print job, you have printed...
Yellow and Black Mixing Together Nozzle Checks or Prints mPower
customer
Symptoms: When doing a nozzle check or printing yellow a small amount of black is mixing in the color, this is only with the mP5. When printing a graphic that is yellow with a black border, the black bleeds into the yellow. Both mP5 and mP10 Possible Causes: When printing...
Creating the Right Environment for Your AnaJet mPower Printer
Dean Armando
In this post, we'll guide you through the key steps to create an optimal environment for your AnaJet mPower printer. Whether you're a seasoned user or just starting out, setting up the right conditions is crucial for achieving top-notch printing results.
Anajet mPower Garment Printer Daily Maintenance Guide
customer
Ensuring your printer stays in top condition is crucial for maintaining consistent, high-quality prints. By following a few straightforward steps, you can guarantee that your printer operates at peak condition.
AnaRIP 4.0 RIP Software Installation Guide
customer
Welcome to our AnaRIP 4.0 installation guide! Whether you're a pro or just diving into it, our video will help you breeze through the setup.
Weekly Maintenance on the Anajet mPower Printer
customer
CLEANING SOLUTION LINT FREE WIPES SWABS MPOWER PARTS
Anjanet mPower Ink Dripping from Print Head
customer
Symptoms: Nozzle check pattern has large gaps Drops of ink appear on shirt when printing Visible dripping from print head plate Possible Causes: The print head surface may be dirty. Perform a print head clean 1 from the main menu followed by a nozzle check. Print head plates need to...