Support ArticlesDTG

Your browser does not support the video tag. If the Nozzle Check is not good, you will need to perform a Print Head Clean. A Print Head Clean is performed from the Printer Control Panel under the Main menu. Press the<MENU> button and select Print Head Clean and press <ENTER>....

The Encoder Strip located on the back of the carriage should be cleaned on as needed if becomes covered in ink mist or if ink has landed on the strip. In order to clean the encoder strip, you will need to first release the print carriage. From the Maintenance menu...

Check the Ink Drip Foam located on the left and right sides of the printer regularly. Replace them as needed when they are soaked with ink or excessive ink residue builds up. If you use a lot of white ink, you will have a more rapid buildup of ink residue....

Your browser does not support the video tag. Now that the lines have been filled with ink you will need to perform a Nozzle Check. First we need to set the table height by pressing the <AnaJet> button. This will lower the table, move it into the printer and raise...

Learn how to set up your Kothari software to work with the Katana DTG Garment Printer. Get ink and supplies for your Katana Garment printer.    

Learn how to replace, clean or repair the Print Head on your DTG Viper 2 Garment Printer.  buy Dupont ink and learn how to Refill the cartridges on the DTG Viper 2 Garment Printer     Buy DuPont ink for your DTG Viper 2  

There are many reasons you may need to take out a print head on the Anajet mPower MP5 or MP10.  Whether it's to clean or replace, watch this video to learn how to make this common repair on your Anajet Printer. If you need to CLEAN your Anajet mPower print...

Learn how to take apart the Katana DTG P600 Garment printer.  Buy Ink for your Katana DTG Garment Printer. Buy Parts for your Katana DTG Garment Printer  

Learn how to remove the control panel on the Anajet Sprint Garment Printer. Buy Parts for the Anajet Sprint Buy Ink and Supplies for the Anajet Sprint Learn more about the Anajet Sprint (1) Remove the two Phillips (+) screws that hold the Control Panel to the printer body. These...

Learn how to Install the Anajet Sprint Capping station.  The capping station controls pressurization and the flow of ink.  Many people think they have a clogged head when it's really the pump in the capping station or the Maintenance station is clogged.  Replace your capping station every 6 months if...

Learn how to remove the Anajet Sprint Capping station.  The capping station controls pressurization and the flow of ink.  Many people think they have a clogged head when it's really the pump in the capping station or the Maintenance station is clogged.  Replace your capping station every 6 months if...

1. Power On/Off Switch Press ( | ) to power the unit on and press (O) to turn the power off. 2. Hose Inlet Connect 1/4” OD hose to inlet for pretreatment solution supply to the Pearl PTM. 3. Rail The Nozzle Cart glides on the rail. Ensure proper lubrication...

1. All Purpose Cleaner Used to clean the Pearl PTM after use. See “Keeping the Pearl PTM Clean” 2. Shop Rags or Towel Used to clean the Pearl PTM after use. See “Keeping the Pearl PTM Clean” 3. Distilled Water Used to clean the Pearl PTM after use. 4. 3mm...

The Pearl PTM is powered with either 110V/60Hz or 220V/50z. Please check with distributor to verify the power requirements for the Pearl PTM in your region. 1. Plug the power cord in to the power connector located on the right side of the Pearl PTM. 2. Press the Power Switch...

Home Menu 1. Start/Stop Button Press to start or stop spray cycle. 2. Light Pretreat Level Meter Displays estimated light pretreat remaining. 3. Dark Pretreat Level Meter Displays estimated dark pretreat remaining. 4. Garment selection Displays garment selection: light or dark garment. 5. Spray Length Area Displays spray length setting....