Support ArticlesDTG

Priming the Pearl PTM is required for proper spray pattern on the garment. If the Pearl PTM is improperlyprimed, you may not get an even, flat and consistent spray pattern on the garment. 1. To prime the machine, enter the Maintenance Menu by selecting the Maintenance Menu icon.2. Place the...

 The settings will allow the user to control the spray density and spray length. 1. To adjust the settings, enter the Settings Menu by selecting the Settings Menu icon. 2. The Spray Density can be adjusted by pressing the Spray Density Setting and entering a value between(20 – 100).3. The...

Loading the garment properly will ensure even, consistent spray patterns. 1. Place the garment on the Platen as shown in the figure below with the collar of the garment towards thecontrol box.2. Tuck the excess fabric under the platen.     Buy the Pearl PTM Pretreatment Machine here Read a...

The Spray Cycle is the process the Pearl PTM uses to lay a flat and even layer of pretreatment solution on to the garment. 1. To begin the Spray Cycle, enter the Home Menu by pressing the Home Menu Icon.2. The Home Menu will display the current garment selection, spray...

When changing pretreat it is important to follow these steps to ensure proper function the the Pearl PTM. The internal volume (mL) counters use these maintenance buttons to calculate the estimated usage. Incorrectlychanging the pretreatment may result in incorrect volume (mL) counting for the Pearl PTM. 1. To change the...

When anticipating extended periods of non-use of the Pearl PTM, it is critical to follow these maintenance procedures. It is required to follow these steps daily after each use of the Pearl PTM. 1. To flush the Pearl PTM, enter the Maintenance Menu by pressing the Maintenance Menu icon. 2. Remove...

 The Pearl PTM stores setting and cycle information, as well as estimated pertreatment container levels during power off. It is important to follow these shut down procedures to allow this information to be stored correctly. The Pearl PTM will not allow the unit to properly power down with pretreatment solution in the...

 It is important to keep the Pearl PTM clean during extended use. The pretreatment solution can build up salt deposits that can inhibit normal operation of the Pearl PTM. It is recommended to clean the inside of the Pearl PTM after ten shirt cycles to prevent build up of pretreatment that may...

 The Pearl PTM has a save feature that allows users to save settings and modes. The save feature will allow up to twenty files to be stored in the memory of the machine. 1. To save the current settings, open the Save Menu by pressing the Save Menu icon. 2. The...

 The Pearl PTM is equipped with a cost calculator that allows users to determine the cost of pretreatment used on a single shirt or the cost for a run of shirts. 1.Entering Pretreament Cost: Enter the Stats Menu by pressing the Stats Menu icon. Press the Cost/Gal # for either the...

 The Pearl PTM is equipped with a speed mode that will allow multiple shirts to be loaded and sprayed quickly. Additionally, the Pearl PTM has a Flexlock Mode which allows garments to be loaded from the front to spray a smaller area for pocket or crest prints. Enable Speed Mode:1. To turn...

 With normal use of the Pearl PTM, a few routine maintenance procedures will be required to follow to ensure proper operation. If desired operation is not within the range of factory default settings, the motor and auto prime timing can also be adjusted. 1. Tightening the Belt. The belt drive system may...

If you experience Possible Causes Solution Leaks Pretreatment solution dripping from Solenoid Hose may have come loose. Push hose in to quick connect Excessive pretreatment solution dripping from nozzle Nozzle Cap is loose Tighten Nozzle Cap Nozzle O-Ring is not installed Install Nozzle O-Ring Pretreatment leaking from bottom Pump Hoses...

  1. All Purpose Cleaner Used to clean the Pearl Lite after use. See “Keeping the Pearl Lite Clean” 2. Shop Rags or Towel Used to clean the Pearl Lite after use. See “Keeping the Pearl Lite Clean” 3. Distilled Water Used to clean the Pearl Lite after use. REPLACEMENT...

  The Pearl Lite is powered with either 110V/60Hz or 220V/50z. Please check with distributor to verify the power requirements for the Pearl Lite in your region. 1. Plug the power cord in to the power connector located in the back of the Pearl Lite. 2. Press the Power Switch...

  Priming the Pearl Lite is required for proper spray pattern on the garment. If the Pearl Lite is improperly primed, you may not get an even, flat and consistent spray pattern on the garment. 1. To prime the machine, enter the Prime/Purge mode by pressing the Density Up &...