Support ArticlesDTG

  The Density settings allows the user to control the amount of pretreat solution to apply to the garment. 1. To adjust the Spray Density, press either the Up or Down Density Button (4). 2. The Spray Density setting will be indicated by the Display. The lower limit is 20...

  Loading the garment properly will ensure even, consistent spray patterns. 1. Place the garment on the Platen (5) as shown in the figure below with the collar of the garment towards the top. 2. Tuck the excess fabric under the Platen (5). 3. Push the Platen (5) in to...

 The Spray Cycle is the process the Pearl Lite uses to lay a flat and even layer of pretreatment solution on to the garment. 1. With the garment loaded to the desired spray length, press the Start Button (9) to begin the Spray Cycle. 2. The Spray Cycle can be...

 When flushing pretreat solution it is important to follow these steps to ensure proper function the the Pearl Lite. These steps should be followed prior to switching pretreat solution. 1. To flush the pretreat solution, enter the prime/purge mode by pressing both the Up & Down Density Buttons (4) simultaneously....

 It is important to keep the Pearl Lite clean during extended use. The pretreatment solution can build up salt deposits that can inhibit normal operation of the Pearl Lite. 1. Use shop rags or towels to regularly wipe off excess pretreatment inside the machine. 2. Use All Purpose Cleaner on...

 With normal use of the Pearl Lite, routine maintenance procedures will be required to follow to ensure proper operation. 1. Lubricating the Slides. If low spray densities are desired, proper lubrication of the rail system is required. 1. Spray the rail with a silicone based lubricant. 2. Move the Platen...

If you experience Possible Causes Solution Leaks Pretreatment solution dripping from Solenoid Hose may have come loose. Push hose in to quick connect Excessive pretreatment solution dripping from nozzle Nozzle Cap is loose Tighten Nozzle Cap Nozzle O-Ring is not installed Install Nozzle O-Ring Pretreatment leaking from bottom Pump Hoses...

1. Power On/Off Switch Press ( | ) to power the unit on and press (O) to turn the power off. 2. Hose Inlet Connect 1/4” OD hose to inlet for pretreatment solution supply to the Pearl Lite. 3. Display Indicates the Spray Density setting with a range between 20...

  Your safety and the safety of others are very important. We have provided many important safety messages in this manual. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can injure you or others. This symbol will...

  Your safety and the safety of others are very important. We have provided many important safety messages in this manual. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can injure you or others. This symbol will...

Learn how to repair/replace the print head on the DTG M2 / M4 Garment Printer 

Here is a video on replacing the carriage belt on the DTG Kiosk 2 

This is a video showing you how to replace the PF encoder belt on the DTG Viper.

Unfortunately filled cartridges and bulk cartridges are not available for the DTG Viper 2 (only prefilled from COLDESI or Colman and Company) however it is very easy to refill the cartridges that you buy from them.  Whether it's with DuPont ink or Image Armor ink. Watch the video to see how...

If the needle is really clogged, then you want to prevent the dried up ink from going to the print head or dampers. So if you are sure that there is a clog before the damper or the print head, then you are going to want to look at doing...

Lean how to install or repair the capping station (maintenance station) on your Neoflex garment Printer Buy a Pump and Capping Station (maintenance station) for your Neoflex Garment Printer here